Biamp Tesira Firmware 5.7.2 and Discovery Tool 1.2: A Dante Checklist for Dublin

Banner from the Biamp Tesira firmware news: a Devio SCX 400 and a TesiraFORTÉ X 400 with green status lights, below the title Biamp Discovery Tools 1.2

Biamp Tesira firmware 5.7.2, published by Biamp in November 2026, fixes Dante channel names that fell back to their defaults and Dante Domain Manager enrolment faults, and lets Tesira devices take bulk channel renames from Dante Controller. Biamp released Discovery Tool 1.2.0 at the same time, so Dublin teams can once again find Devio SCX and TesiraFORTÉ X processors set up with Biamp Launch when they run firmware 5.7.0 or later.

Product image: Biamp.

  • Tesira 5.7.2 is a maintenance release covering Tesira, TesiraFORTÉ and Voltera D and D M amplifiers, released in November 2026.
  • Biamp says custom Dante channel names could revert to default names, resulting in loss of audio, and 5.7.2 resolves this.
  • Dante devices that could not enrol in or locate a Dante Domain Manager by its fully qualified domain name are fixed too.
  • Bulk Dante channel name changes sent from Dante Controller are now accepted by Tesira devices.
  • Discovery Tool 1.2.0 resolves an issue that stopped it discovering devices on firmware 5.7.0 and later.
  • Voltera D and D M amplifiers moved to 5.7.1 from firmware older than 5.0 had a communication fault, which 5.7.2 also resolves.

Two releases in one Biamp notice

Biamp's November roundup pairs a firmware update with a small but useful software tool. The firmware is aimed at the DSPs and amplifiers themselves. The tool is what an engineer opens on a laptop to locate those devices on the network.

On the tool, Biamp is direct: "This release resolves an issue that prevented the tool from discovering devices running firmware version 5.7.0 and later." In practice, a team that updated its TesiraFORTÉ X processors earlier in the year and kept an older copy of the Discovery Tool may have found the units no longer appeared. Biamp recommends updating to 1.2.0 so that all devices are discovered, whatever firmware they run.

We covered the previous release in our post on Tesira firmware 5.7.1. This one follows up with a strong Dante focus.

The Dante fixes in Biamp Tesira firmware 5.7.2

The Tesira release notes list five Dante related changes. In plain terms:

Channel names that would not stick. Custom Dante channel names on Tesira devices could revert to their default names, and Biamp records the result as loss of audio. In a working building, that is the fix most likely to matter.

Renaming in bulk. Tesira devices now accept bulk name changes from Dante Controller. On a large system, naming channels one at a time is slow, and Biamp presents this as a way to make naming in large systems faster.

Enrolment by domain name. Before 5.7.2, Dante devices could fail to enrol or to find the manager when it was addressed by a fully qualified domain name.

Recovery after losing the manager. Biamp lists a fix for Audio-Technica microphones in a Tesira system enrolled in Dante Domain Manager that would not regain Dante control communication after the connection to the manager dropped.

A rare error on DAN models. TesiraFORTÉ DAN Rev B and later units enrolled in a Dante Domain Manager could, rarely, report a device internal software error. That is resolved too.

A pre update checklist for Dublin sites

Before anyone presses Update Firmware, work through these points. They come from Biamp's release notes, its normal Tesira firmware update procedure and its update path guidance.

  • List what you have. Note every Tesira server, TesiraFORTÉ, expander, Voltera amplifier and NPX paging station, with its current firmware version.
  • Check the path. Biamp's update path guidance says anything still on 4.x must step to a 5.x version below 5.7 first, ideally 5.6.1, before going to 5.7 or newer.
  • Update the software. Biamp asks for the latest Tesira Software and Biamp Canvas before the firmware goes on. Its downloads page shows Tesira Software 5.7.0 at the time of writing.
  • Back up. Save the running configuration file, and any Canvas file, to a computer. Biamp calls this optional but recommended in case the update is interrupted.
  • Book downtime. All audio stops during the update. Biamp gives 5 to 15 minutes as typical, with up to 15 more for expanders configured in the system.
  • Be on the network. Biamp advises against updating over WiFi or a remote internet connection.
  • Get Discovery Tool 1.2.0. Install it before the update so Launch configured processors stay visible afterwards.
  • Note the known issue. On TesiraFORTÉ X and TesiraCONNECT, the Enable IGMP Querier setting stays disabled whatever Tesira Software shows, although Biamp says joining a multicast group still works.

What this means for Dublin offices and campuses

In a larger Dublin building, one Dante network can carry audio between meeting rooms, an atrium, a canteen and a training suite. Picture a tech company spread over several floors in the Docklands, or a college with lecture rooms in more than one building. Each might have dozens of named Dante channels and perhaps a Dante Domain Manager run by the IT team. Those are exactly the setups where a reverting channel name or a failed enrolment turns into a call to the helpdesk.

For smaller sites, such as a professional services firm in Ballsbridge with a handful of meeting rooms on TesiraFORTÉ X, the Discovery Tool fix may be the more practical part of the news. Our post on Biamp voice reinforcement at Emory shows how the same platform scales up to a campus, and our education AV page covers teaching spaces.

1Install designs, supplies and installs meeting rooms, Teams Rooms and audio systems for buyers across Dublin. You can read about our Teams Room installation in Dublin, our audio conferencing and meeting room AV work, see how we run a project, or price a room in the commercial quote builder.

Questions we are often asked

Does Biamp Tesira firmware 5.7.2 fix Dante channel names resetting?

Yes. Biamp's release notes say 5.7.2 resolves custom Dante channel names reverting to default names, a fault that resulted in loss of audio.

Can I rename lots of Tesira Dante channels at once?

Yes. From 5.7.2, Tesira devices accept bulk Dante channel name changes made in Dante Controller.

Does Tesira work with Dante Domain Manager?

Yes, and 5.7.2 fixes Dante devices that could not enrol in or locate a Dante Domain Manager addressed by a fully qualified domain name.

What does the Biamp Discovery Tool do?

It finds the IP addresses of Devio SCX and TesiraFORTÉ X processors configured with Biamp Launch. Version 1.2.0 can see devices on firmware 5.7.0 and later again.

Is there a known issue with Tesira 5.7.2?

Yes, one. Biamp says the Enable IGMP Querier setting on TesiraFORTÉ X and TesiraCONNECT is disabled regardless of the setting shown, while joining an IGMP multicast group works as expected.

Book a consultation or call our Dublin office on 01 906 9326.

Start a conversation

Let's plan your space together.

Tell us a little about your project and a member of the team will be in touch.

Contact us for a meetup to discuss your needs

WhatsApp us